LIMA Fish Feed Machine,Chicken Feed Machine
The part of the finished product exceeds the standard. Local moisture exceeds a certain concealment, it is difficult to discover. It is the main reason why most of the moisture exceeds the standard. According to long-term observations, the following conditions can cause local moisture to exceed the standard. XY6 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
(1) There is no problem in the technical state of the equipment, and the initial water of the raw materials also meets the requirements but each batch is When the production is low, the steam line deposes a certain number of condensate water, the temperature is high, the temperature is low, and the temperature of the cooler is also poorly active, and it is not easy to dissipate. This part of the particle water will tend to exceed the standard after cooling. Solved method: First, the condensed water of the steam system must be discharged before the production. The granulator has just been removed, and the cooler must not be put into the cooler until the conditioning temperature reaches 50 ¡ã C to the cooler. The 2-4 package of each batch is taken back to the machine processing. XY6 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
(2) Equipment Regulation is unreasonable or equipment failure: Most feed mill cooling process is: cyclone dust collector The recovered material is separated, and there is no special lift back to the warehouse, but directly enter the finished lift. The powder moisture separated by the dust collector does not exceed the standard (the powder is overdered, it will be sieved) but if the cooler’s ldquo; the level switch rDQUO; is too high, the cooler cannot be normally drained or The gas-out of the cooler is too large, etc. For the reasons, the particles of the just granulated granules are sucked into the cyclone, and the particles are not sufficiently cooled and dried, and they are separated, and enter the finished lifter mixed into normal particles. Another situation is that the cooler is not fully cooled during the production process due to unreasonable or positioning switch faults. These materials will have a mildew in the short term, which is manifested as a sporadic mildew, which is constantly evolving into a bag, and the insects and fever are developed. The method of solving is: a, select sensitive ldquo; material sensor rdquo; and positioning switch; B, ldquo; footer rdquo; C, C, conditioning fan, wind door opening, control The cooler outlet is negative pressure. D. The overlapping of the cooler or the overlapping of the fence should neither make the ventilation area too narrowly to avoid leakage in the production process. XY6 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
(3), the internal load of the cooler is uneven: the cooler bulk, the cloth discharge is uneven or individual cooler The cause of the screen is insufficient by the sieve. The cooling time and the cooling intensity of the feed in the cooler are uneven. Partial wet heat exchange is insufficient, and moisture exceeds the standard. In the future storageA sporadic mildew in the middle. The method of solving is by adjusting the dispensers, a cloth, and a tetrangle, cleans the feed to the screen in the screen to match the cooling time and cooling intensity of the feed in the cooler. XY6 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
ldquo; Pot Bar Type rDQUO; Mildew: In Production Process Medium-granulator ring-shaped cover, granulator’s descending tube, the dead angle of the cooler adsorbs a large amount of high moisture ldquo; pothamine rdquo;, they are adsorbed into the feed when adsorbed to a certain thickness. Due to this ldquo; Pot Bar Support Rdquo; in the formation process, in the formation process, the starch is very high in color, which has created favorable conditions for the reproduction of molds, and they have metyatomy before falling into the feed. . After cooling together with feed, the moisture is still high as 15% mdash; 25%. These ldquo; Pot Base Rdquo; If the delivery device and the hierarchy screen are broken into large and small irregular blocks, the large blocks of these blocks cannot be removed by the upper screen of the hierarchy. The smaller blocks are mixed into the feed through the upper screen of the hierarchy. These already mildew high water blocks are easily induced by the surrounding feed particles. The solution is to remove the cycling machine’s ring cover, granulator’s lower tap, and the corner of the granulator. .
XY6 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
(5) The water branch is raised and is prone to mold. Sichuan’s feed mill often encounters such a complaint in summer: Feed in the customer’s home stores with the phenomenon of molding, fever, and pest. For the finished package, the first is the packaging bag. The inner and outer bags are intact, and the second is to crosstose when the seam is seam, to reduce the contact of the feed with external air.
XY6 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
(6) Select reasonable antifillurantant: add an appropriate amount of high-quality antimoderans in production to effectively inhibit Mold growth, prolonging the preservation time of feed. XY6 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
