LIMA Fish Feed Machine,Chicken Feed Machine
5K3 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
1 Small Feed Factory often uses a low pressure steam boiler, and the steam used The pressure is typically 0.2 ~ 0.4 MPa, and the steam boiler is also placed near the granulator. Due to the low output, the transport distance is short, the granulator ring is small, and the granulator ring is small (general phi; 2 ~ pHi; 3), Its particle quality is better; 5K3 China feed industry information network – based on feed, serving animal husbandry
2 large feed mills due to high yield, more equipment, and steam boilers are generally away from production workshops, so The conveying pipe is longer (usually in a few hundred meters), which is often used high-temperature high pressure steam to ensure the quality of the granulator. 0.8 MPa and 180 ¡ã C saturated steam are generally used. 5K3 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
From our experience, the steam boiler should be placed near the granulator, try to shorten the length of the steam pipeline, especially in the north; In addition, the steam boiler should give priority to the oil furnace, which is difficult to ensure the stability of the steam pressure due to the coal furnace. Otherwise, the water content of the steam is high, the steam pressure is unstable, which in turn affects the conditioning effect, affects the quality of the particles. 5K3 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
5K3 China Feed Industry Information Network – Bit Feed, Service Animal husband The granulator (8T / h) used in a feeder in the north, the length of the mass strip length 1.4m, due to the increase in the alternative raw material added in the feed in recent years, in the northern winter Cold weather and conveying pipelines, long conditioning time is too short, the temperature is low, and the tuning effect is difficult. Therefore, the conditioner selected by the northern feed mill granules should be enhanced to ensure the temperature and time of the powder feed, thereby ensuring the quality of the particulate feed.
5K3 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
5K3 China Feed Industry Information Network – Based on the feed, service livestock
The clearance is guaranteed to be rotated at 0.05 to 0.3 nm, that is, the ring model is rotated, and the roller is rotationally rotated. At a large clearance, the wedge space between the mold rolls will fall into the feed, and the mold roll is reduced to the extrusion of the feed. When the pressure is smaller than the inner wall of the mold hole, the granulator will block, affect Particle quality.
5k3 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
When replacing the ring mold and pressure roller, it is best to pairFor normal production, adjust the diaphragm clearance before the start of each shift; when the old ring mold and the pressure roller should be worn, it should be made to ensure its surface is flat.
5K3 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
When checking the granulation, if it is found that the pressure roller is not rotated in a timely, the general situation is timely. Under
5K3 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
Molding Diameter and Intrava Hole: In the case where the thickness of the ring mold is constant. The diameter of the mold is reduced, and the strength of the feed particles is increased by the extrusion, the particle type is neat, the hardness and density is improved, and the powder is lowered. The mold hole is pHI; 2 to pHI; 3 feed particles are beneficial to the breasts of the lactar and chicks. Of course, the diameter of the ring model is reduced, and it will inevitably lead to a decrease in production efficiency. Therefore, it is necessary to integrate the above factors for reasonable selection.
5K3 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
If the feed cone hole of the ring mold has severe wear, granulation production and particle quality will fall. Because, the amount of steam added at this time is limited (the amount of steam is large, which will block the machine), thereby lowering the feed massage temperature. Therefore, when the ring mold is still available, the feed tapered hole of the ring mold should be machined to ensure yield and particle quality.
5K3 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
5K3 China Feed Industry Information Network – Bit Feed, Service Animal husbandry 1 Particle cooling is uniform moderate, now there is more use of countercurrent cooler, its cooling efficiency is high, good effect;
5k3 China feed industry information network – based on feed, service animal husbandry
2 Particle Crushing Equipment Note When the crushing roll is blunt, it should be repaired in time. Otherwise, the extrusion of the broken tooth roll is so strong, and the particle uniformity of the feed is deteriorated, and the powder increase high. When producing, according to the feed variety correctly adjust the broken roller clearance; 5K3 China feed industry information network – based on feed, service animal husbandry
3 granules After crushing, apply sieve angle The plane rotary grading screen is sieved, especially the large feed mill, and when the sieve angle is too large, the particulate sieve is not sufficient, resulting in a powder of the particle material. 5K3 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
