LIMA Fish Feed Machine,Chicken Feed Machine
(1) Check, debugging PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
1, adjust the cutter position away from the ring Open the granulator door, (replace the ring mode according to the need to replace the ring mode) to clean the compression chamber; check if the hug bolt and the fixed screw of the bolt bolt and the pressure roller are tightened; the mold roll gap (about 0.1-0.3mm Whether it is appropriate, under the rumor is driven, it is similar to the rotation; whether the position of the blade is in place; rotates the moving parts by hand to ensure that it is not stuck. PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
2, follow the lubrication map to fill the lubricants. PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
3, check the permanent tub, feeder, striupter, may have hemp rope, iron filings and other debris; Start the feeder, the mass strip is empty, ensuring that its operation is correct, no abnormal sound; the feeder stops in a low speed state. PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
4, the condensed water in the distinguished cylinder is discharged, checking whether the pressure gauge is normal. PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
5, Start the main motor (this operation is mainly suitable for new machines or line-modified machines, do not open the door without opening the door Make sure that all of the operating components in the granulator are normal, ensuring that the ring mold is rotated in front of the clockwise direction, and the surface of the pressure roller is slightly contacted with the inner surface of the ring mode, and the rotation of the ring mold is achieved. Stop after it is correct. PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
6, close the machine door, adjust the cutter, so that the knife die is gap (not less than 3 mm) to meet the production of this class need. PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
PG4 China Feed Industry Information Network – Bit Feed, Service Animal husbandry
1, the equipment that starts the granulator rear process.
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
2, the granulator main motor is started.
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
3, start the mass motor.
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
4, start the feeder motor. The electromagnetic speed motor is adjusted to a low speed, so that the feed is slowly entered into the stront, granulator pressing chamber.
PG4 China Feed Industry InformationNet – based feed, serving livestock
5, when the granulation is started, do not add steam, slowly increase the feeder feeding speed of the feeder according to the main motor current.
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
6, slightly open the steam valve, to be the main motor current to decline, then increase the amount of feed, so that the main motor current is close to normal After the load, the amount of steam is increased to decrease the main motor current. This is repeatedly operated until the main motor is the highest in the rated load, and the quality of the particles is best.
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
7. It is guaranteed that the granulator current is running within the rated current, and must not operate overload.
China feed industry information network – based on feed, service animal husbandry
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry [ 123] 1. Turn off the steam and feeder (both interval time as possible). PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
2, let the granulator continue to operate until the formation is stopped, then the regulator, if the machine needs to stop for a period of time At the time, it is necessary to add an oil-containing powder to the manual feed opening until the particles are formed. If it is from get off work or long, the inner holes in the ring die should be filled with oil. PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
3, turn off the main motor. PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
4, cut off all power supplies after get off work. PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
1, during the production process, the material of the granulator is large, and when the current suddenly rises, the machine is required to be discharged from manual discharge mechanism.
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry When you need to open the granulator door, you must first turn off the power supply, and after the granules are completely stopped, Open the machine. PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
When restarting the granulator, the granulator must be manually turned to activate the granulator. .
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
4, when the machine fails, the power supply must be cut off, the stop is excluded, it is strictly forbidden to operateHard exclusion with hands, foot, wooden sticks, and iron; strictly forbidden to start motor.
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
5. When using new ring molds for the first time, a new roller must be used, and the oil can be done with the sand (all pass 40-20 mesh sieves, matching: oil: Sandy is 6:2:1 or 6:1:1) Flush ring mold 10 to 20 minutes, you can put it normally.
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
6, assisting repair work to the main motor bearings every year.
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
7. Assist the maintenance of the granulator gearbox to replace the lubricant 1-2 times a year.
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
8. At least 2 times per class per class.
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
9. The steam pressure in the jacket jacket is not higher than 1 kgf / cm2.
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
10 It is suitable).
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
11, each shift is given 2-3 times.
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
12, 2-4 of the feeder and striups per week (clean every day every day).
PG4 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
13, the distance from cutters and ring modes is generally not less than 3 mm.
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
14. When producing, the main motor current is strictly forbidden to exceed the rated current, an overload operation.
PG4 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
