LIMA Fish Feed Machine,Chicken Feed Machine
Particle feed mechanism is also known as pressed machinery, its effect is to add a good semi-finished feed to sugar water, etc., according to the feeding characteristics of poultry and the habitual processed into granular feed. Common feed particles mechanically include several soft particle feeders, hard particulate feeders, puffed particulate feeders and multi-functional particulate feeders. Among them, the hard particle feeder is also divided into a cyclic mold pressing machine and a flat die press. China feed industry information network – based on feed, service animal husbandry
94C China feed industry information network – based on feed, service animal husbandry 1. The particle feeder should strictly select the feedstock and design scientific feed formula when making feed.
94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
2. The machine should be smoothly installed, and the power supply is connected in accordance with the rotation direction of the machine.
China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
3. After installation, there should be no loosening of each site screw; the transmission belt must be moderate; two roller and The balance between the grinding discs, the gap between the roller and the grinding disc is 0.1 mm to 0.3 mm.
94C China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
Water is 0.62 kg, 2 kg of sand), and stir evenly, and ground it for about 30 minutes with a modified abrasive.
94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
5. After the installation is correct, stir the bullets in accordance with a certain proportion requires uniformity (per 100 kg dry feed against water 3.5 It is best to join the jug), first add the feed mouth, after the particle feed is extruded, fill the material normally produced.
94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
6. The length of the particles depends on the length of the body’s outlet, which can adjust the high and low position of the cutter on the upper end of the discharge. The length of the particles is adjusted, and the diameter of the particles depends on the aperture of the grinding disc, and the size of the grinding disc is required to make the size of the feed diameter. The flat particles generally adjust the long short cutter in the discharge port, which can be adjusted according to the actual needs; the ring mold particles are mainly adjusted by manual (or electric) cutters outside the body.
94C China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
7. It is strictly forbidden to stir the feeding in the addition bucket.
94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
8. Hard or gold in materialsThe block should be cleared.
China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
94C China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
1. The new machine requires rinsing each time it is used, and after 15 times to 20 times, it is no longer flushed. 94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
2. The particle feeder should use the supporting power according to the instructions. Over small, low output, poor effect; too large, waste, accelerator wear, shorten service life.
94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
3. After 1000 kg of particles, the template needs to be used back, avoiding shortening service life.
China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
4. Frequent cleaning equipment floating and dirt on the outside of the equipment, and regularly add lubricating oil to ensure that the particulate machine is in good lubrication Lower work.
94C China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
5. The residual feed in the ring die cavity is often removed.
94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
6. In the production of two roller eccentric shafts, in the production of each shift.
China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
7. Regularly check the ring mold, pressure roller, cutter, paddle, transmission belt, etc., to adjust in time Or replace, make sure the particles are working properly.
94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
8. Maintenance and Maintenance of Pressure Wheel and Transmission Parts. Every 2 ~ 5 working days, the bearing must be cleaned and the high temperature grease is obtained as required by the specification. The spindle is cleaned every other month, and the gearbox is to be cleaned in half a year, and the screw fastening replacement of the transmission portion should be performed at any time. After the press wheel is worn, the pressurized ribbon can be replaced or replaced with a set of pressing wheels; it is found that the bearing is loose, and the bearing should be replaced with the bearing or connecting. The ring molding of the ring type particles is aging, wear, after injury, replacing the new piece.
94C China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
The bolts in the granulation of the granulation, the bolt and the scraper have no loose phenomenon. 94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
10. You should check the gap of each pressure roller and ring mode before driving, and adjust the roller and ring die.123] 94C China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
11. The distance between cutters and ring mode is strictly inspected, and it is not less than 3 mm. 94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
At any time checking the machine. 94C China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
