LIMA Fish Feed Machine,Chicken Feed Machine
Particle processing is a deep processing process. From the improvement of components such as striup, granulator and dawn machine, to the design of the cooler, the granulation is stable, and the liquid adding system, these processes affect the quality of the particulate feed. TWB China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
Revenue high temperature, high pressure and high moisture, high-sensitive, easy oxidation and solubility substance are extremely unfavorable , Especially vitamins and enzyme preparations. If the greenhouse is too high and the moisture content is too low, it will promote the US Raid reaction, leading to the reduction in protein’s digestibility and the amino acid titer, which requires processing and regulation, saturated steam, avoiding the use of wet steam, steam temperature Control minimum in normal production. TWB China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
TWB China Feed Industry Information Network – Based on Feed, Service Animal Husbandry [123 Temperpins causes material heat to promote starch and sterilization. Multi-stage tuning temperance increases the injection molding effect by extending the tuning, the starch deactivation can reach 40% to 60%. After granulation, mosquitmenting temperance is to heat the granules (about 70 to 80 ¡ã C), allowing hot particles in a high temperature and high humidity in a period of time, so that the starch in the particulate feed is sufficiently changed, and protein sufficiently denaturation . High pressure gap expansion regulation is an advanced, new method for mass-conditioning treatment for powder feed, only a few seconds, but the maximum pressure can reach 100MPa, the maximum temperature can reach 170 ¡ã C, make material energy energy Fully touched and mature. TWB China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
The particulate feed of different ingredients requires different regulating temperatures. According to the good feed, in general, the temperature of the grain is high, the moisture is more, so it is conducive to the starch amylization in the grain, and the substance after the plant has a binder, which is conducive to production. Founded particle feed. Generally, the temperature of 85 degrees Celsius, the water added by the regulation is 4% ~ 5%, and the moisture content after the injection is 17% ~ 18%, and it seems to be a group and is not a group, so that It can improve feed yield and save dry costs. For feed containing high crude protein, the temperature regular temperature can be lower, with 60 to 70 degrees Celsius, and the moisture is added at 1% to 2%. If the temperature is too high, it will gently block the mold hole. TWB China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
TWB China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry [123
The aperture size of the molding can be determined according to the produced feed species. Particle size is dependent on two factors, one is animalFeeding behavior, such as piglets better than small particle feed; another is the production efficiency of granulator, using a large diameter of the mold hole, and the product is high, and the energy consumption is small. The report of particle size on pig growth performance is still uncomfortable. Traylor et al. (1996) reported that the pigment of the pigs in 5 days ago, the positive level increased and the feed conversion rate, and the powder is increased by 25% and 36%, the particles diameter (2 to 12 mm) does not affect pig growth performance. The pig daily weight and feed conversion and feed rate of 4 mm were the highest in pig days during the age of 0 ~ 29 days; the growth rate of pigs in 29 days-aged ~ fertilizer period was not affected by feed morphology, but the feed transformation of particles The rate is better than the powder. Stark et al. (1994) reported that when feeding piglets with sieving pellets, the feed conversion increased by 4.5% higher than the particulate material containing 15% or 30% fine powder. Peter (1998) believes that for different aged pigs, 2.5mm can be widely accepted, but the diameter of the pigment of piglets is preferably 2 mm. Hancock et al. (1999) believes that pig feed is more suitable for a single 4mm-5 mm particle diameter, which can significantly save time and investments for ring molds. TWB China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry TWB China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry [ 123]
The feed which is made of particles removes excess water in the cooling while reducing the temperature. For feeds with grain as major raw materials, the temperature of the material enters the cooler is 75 ~ 85 degrees, and the moisture is from 17% to 18%. After cooling, the temperature is 8 degrees higher than the surrounding environment, and the moisture is around 13%. When cooling, pay attention to control cooling time and prevent the cooler wind circuit short circuit. For large particle feed, the cooling time is longer, the air volume is increased to ensure cooling quality; small particle feed cooling time is short, the air volume is small, so as not to cause ldquo; shrink rdquo; The two-roll gap of the crusher should be paired, and the two-roll gap is three-thirds of the feed to be broken.
TWB China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
