LIMA Fish Feed Machine,Chicken Feed Machine
Hammer-type pulverizer is a machine with high-speed rotating hammers. It has a wide range of energy, weak temperature sensitivity to feed, and has good generic quality, use maintenance and productivity. . However, if the user analyzes several key issues affecting the performance of the crusher, it will make the productivity are not high, the power consumption is large, and the crush quality cannot be guaranteed. This article describes several key issues that should be noted when using a hammer pulverizer and analyze it. China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
3F9 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry [123 Generally, the moisture content of the feed is not more than 15%
3F9 China feed industry information network – based on feed, service animal husbandry Feed Increased water content, decreased structure, decreased feed, feed is not easily pulverized, productivity and degree of electricity production are reduced. The test proves that when the water content increases from 14.3% to 21%, the product rate is reduced by 29% to 12.5%; the water content of barley is increased from 13.8% to 20%, the product rate is reduced by 30% power consumption increased by 12.5%. So general The water moisture content of the feed rate is not more than 15%. 3F9 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
The speed of the hammer has a large influence, with a low value when the pulverized stem feed is pulverized. Take a high value when pulverizing grain feed
3F9 China feed industry information network – based on feed, service livestock The hammer speed has a great impact on the productivity and power consumption of the pulverizer. The test prove that the cracking ability is lowered when the hammer speed is low, and the wind of the suction powder is also small, so the productivity is low, the power consumption is increased. When the speed is high, the pulverization capacity and the powdery ability are increased to increase productivity. However, if the speed is too high, due to the increase in the blast of the rotor, the turbocrinous effect is enhanced, resulting in an increase in no-load power consumption. At the same time, the material is too high, the opportunity to discharge the screen is reduced, so the pulverization efficiency is also relatively lowered. In addition, if the hammer is too high, the power consumption of the bearing friction and agitation air will increase dramatically, so that the energy consumption of the unit product is significantly improved. Therefore, each type of pulverizer has a suitable speed range. In recent years, the pulverizer has improved, and the general farm uses the pulverizer to take a low value when pulverizing the cereal feed when the pulverizer is used. In short, it is necessary to choose the right according to the requirements of the instruction manual. Hammer line speed to give full play to the efficiency of the pulverizer. 3F9 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
Hammer Size Uncommon or Over Small
3F9 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
The hammer sieve is a gap between the end of the hammer and the screen, and the working performance of the pulverizer is large. influence. When the hammer sigmia is large, the feed particles close to the sifter in the feed cannot be easily contacted with the screen, and the hit has a small opportunity, and the frictional effect of the screen on them will weaken due to low speed, so the degree of electricity production decreases. The finished product is thick. When the gap is large to a certain extent, the feed particles on the screen plane are too slow, even blocking the screen, making the productivity further decrease. When the hammer sieve gap, the outer ring feed is much more opportunities to hit the hammer, and the feed movement speed is high, it is not easy to pass through the screen, which makes the friction and pulverizing, and the feed is smashed too fine, even more It is good to drain powder, not only wasted power, but the reduction of electricity production, and the finished product is also fine. 3F9 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
Under the premise of rearing requirements for livestock and poultry, a large number of sieve diameters should be selected [123 ] 3F9 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
The impact of the sieve diameter is very significant, and it also directly affects the fine crushing rate of the pulverized feed. The average diameter of the feed particles). Feed Fields M u003d (0.25 ~ 0.33) d. The larger the diameter of the sieve, the higher the electricity production, the thicker the pulverized material. In general, when pulverized feed, the sieve diameter starts from D u003d 2 mm, each increases by 1 mm, and the productivity can increase by 20% to 35%. Conversely, the smaller the diameter of the sieve, theoret the feed pulverization, but the productivity and degree of electricity production of the machine are also significantly reduced. Therefore, under the premise of satisfying the requirements of livestock and poultry, a larger hole diameter screen should be used. 3F9 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
3F9 China Feed Industry information network – based on feed, service livestock
The model of the crusher is different, and its feeding is different, and it directly affects the impact on the pulverization efficiency. When the amount of feeding amount is greater than the air flow of the screen, the material is collected on the screen, which causes the splitting of the slider to the fluid flow in the pulverized circulation layer thickened to increase the resistance of the resistance on the rotor results in pulverization efficiency. decline. Therefore, when the feeding amount is only in line with the design requirements of the crusher, the power consumption is the smallest, the productivity is the highest, the motor does not exceed the overload, and the user will get satisfactory crushing products.
3F9 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
3F9 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
[123The pulverizer is a high-speed rotating machine, which is moving, and the static balance test is available at the factory.After a period of use, when the hammer corner wears 1/2 of the hammer width, the changing or head must be carried out in place.When the blade of the pulverizer, the blade of the pulverizer is started, and it can also be used.When you need to replace the new hammer, you must researchers and ensure that each group of quality does not exceed 5G, avoiding the balance of the machine to generate vibration and noise. China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
3F9 China Feed Industry Information Network – Bit Feed, ServiceAnimal husbandry
Crushing machine transmission belt quick degree of movable motor to adjust the front and rear positions on the base, to avoid the transmission belt slip, can make it loosely on to increase the inclination angle. 3F9 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
