LIMA Fish Feed Machine,Chicken Feed Machine
Correct use of ring model and pressure roller, small series by collecting accurate and complete production tons record, rarch on single ring mode use, summarizing the following information for peer reference, understanding of processing technology characteristics, roll rolls It is very helpful to use correct use. , Various Type Statistics Statistics: 1, the most important result is to produce tons: feed production ton The number is the basis for valuable costs and production performance. 2, running hours is the same important statistic, because it explains the product flows throughout the product. 3, Metal impurities to stampening is a potential destruction source. 4, Wear Thickness has a great influence on particle quality and production. Serving Livestock 5, Rolling is a flattening effect, closing the mold hole import, reducing yield and increases the pressure stress of the pressure mold. Serving Livestock 6, the honeycomb is partially composed of well-wear wear and maintains stable output. 7, Corruption is a general result of stamping and corrosion, corrosion occurs in the granulation chamber, will reduce yield. 8, and the scotch is formed in the granulation chamber to abrasive into the groove. 9, the clamping surface is a state in which the compact surface is matched. 10, Damage Trim: A, Ring Damage and Pressure Mold Damage Strength Related to serving livestock B, burst occurs when a part of the compactment is falling off from the stamper. There is usually an annular rupture. Service Animal Husbandle C, flange destruction is the result of dramatic or pulled movement. Note and Display Problems: Wear Thickness (Depth) Any Wear Most Combined Pressure and Most The characteristic is the definition of the surface wear of the surface of the compression mold is a vertical distance from the horizontal surface of the symbol initial pressure mold surface to the front surface of the pressure mold. This data is recorded in three different parts: circular cone, central region, and sleeve areas. from the top of the front of the pressure mold, the center and sleeve area reading in their respective regions and the junction of the surface of the pressure mold Measure. OneA good standard method is to measure the precise central part and to each flange side pore, which helps to maintain the constant constantness. The only exception to th locations is that if a region has a special deep wear, the measurement should be placed at the deepest point. Service Livestock For the measured reading, it is briefly removed from the particles in the respective wells. Scraping excess grease, deposition, and other particles that may prevent correctly measured, ensure that the outer surface is cleaned. With a meter or small diameter round rod, insert the micronized depth ruler or small round rod from the mold hole outlet until it appears from the inlet end of the mold hole, the round rod is a symbol or inspection Microcomputer dial reading. You have measured the thickness of the pressure blank, which can be subtracted from the initial blank to obtain a wear concentration, which is given in insertion. the wear depth measurement gives an important information about feed distribution, which can evaluate which part of the stamper is deepened, and this measurement also indicates the wear squeegee and uniform or not. The case of a uniformly wear pressure roll shell. 1, Rolling is a condition in the implantation of the pressure mold working face. This extension effect greatly affects particulate quality and mold yield, often reduces both. The cause of the calendering is the force applied to the surface of the molded surface exceeding the strength of the composite material, and the pressure roll adjustment and certain type feed will apply additional stress in the surface of the die to form an additional stress to form the initial calendering. For MOR MDash; TON and alloy molding, the likelihood of calendering increases with the increase in wear depth, because it has exposed a larger amount of softer material. 2, Honeycomb the formation of animal husbandry is the result of granulation raw material abrasive, which increases the import of the surface of the stamper surface. This effect may result in severe reduction in the two-hole inlet walls, and the top wall from the line to the circular honeycomb characteristic makes the material in the flow molding hole. When the cellular is moderate, it is a marker of a well-produced stamper and is characterized by a chromium chromium material. The illustration shows a general honeycomb and a stample surface state. 3, Metal Extraction Metal impurities refers to any foreign matter in the feed m ure, it enters granulation from some way system. Th foreign objects may be crimped, which interfere with the normal flow of feed in th debris cartridges. Other impurities such as stone, large bones and plastic bags may also enter a plurality of mold blockages. 4, Spot is a state of corrosion formation, it is water, heat andThe result of the co-influence of feed. The spot is reproduced with a small minor corrosion point, and as the pressure is continued. Spots reduced the flow of stamper, reduces the production of compactment, and often reduces the quality of the particles because it produces a rough surface in the mold hole, especially the molding of square particles, because it is more likely to affect the spot. This state can be observed, the method is to remove the feed in a hole, put a lamp in the mold hole, illuminate a hole, look from the hole outlets There will be reaction on the wall of the hole. At this time, the early spots appeared on the inner wall of the hole, as little needle marks, more serious spots will also be displayed, like a large sludge point. Warning: Use a test e cleaner or a pipe cleaning device to ensure that all deposons are removed from the inner wall of the hole. 5, Scotten is the longitudinal la marks along the wall, this trace is due to high baking particulate materials Form it by passing through the mold hole. It is very common that the scotch is taken as the result of the early neighborhood spots in the past, and it is initially spots. The tail is the material to be scratched by the spot zone. Severe scores will reduce the composite yield and reduce the quality of the particles. In this case, it is observed that the method is to clean the feed in a hole. When the diaphragm is imported, illuminate a hole, look down from the hole out of the hole, you can see the difference in the inner wall in the hole, early scratches As small engraved lines, appear on the hole wall, and even more scored in the large trench. Warning: Use Test e or Pipe Clean to ensure that all deposons have been cleaned from the hole wall. 6, Clapped – An important part of any stamping inspection of animal husbandry is a set of inspection of a shaft flange. Th regions are typically damaged due to the adjacent wear compone such as clamps and wear-resistant straps. Therefore, the full purpose of the detection clamping surface is to control the damage to the other compone of the device. There are four surfaces that need to be tested: pine cartridge surface, clamp bottom surface, friction ring surface and keyway. – Battle The front end of the axial flange. There are many reasons for this surface wear, including independent sizes, good sleeve shaft flanges, grinding granulator sleeves, wear composite cartridges, wear friction rings and wear bond channels. Finding the cause of wear is necessary to measure the remaining surface. A Sharpened Case can cause the Songka hoop and the seam surface wear, the seam surface is connected to the sleeve, is pair of Songka hoopnoodle. The wear on both faces may illustrate the need to replace the sleeve. the next sleeve should be carefully examined. the wear on the Songka hoop is caused by the wear of the composite clamp, and should be used to check the appropriate wear regulations provided by the stamper. After cleaning up the surface anti-stick material or rust, it can be observed that the wear is like polished metal. A good way to determine wear is to see polishing during the previous manufacturing process, or hard turning, determine the type of product, and wear can be measured. 8, Clamp Noodle Wear, Casset, Clamp, or Three Common Wears Very serious When the inside of the hoop is wiped to the top of the sleeve and the upper part of the press mold sleeve flange (the bottom surface of the clamp), the clamp falls. This phenomenon can be observed from the performance cleaning of the anti-stick material and rust, and the wear is abrasive. A good test method is to see that the surface is polished during the manufacturing process or harvesting. 9 ring. The polishing and turning type is similar to the previously mentioned, dependent on the origin. This surface wear may be caused by the installation of a wear friction ring or a small-dimensional long guide. The case where the guiding surface size is small is not often reproduced. Most wear of th surfaces is caused by the new molding of the old friction ring. The surface wear indicates that the friction ring should be replaced immediately, and the surface wear also explains the pressing of the pressure and is often the cause of other surface wear of the equipment. Clearing the antisible substance or rust of the surface can see this phenomenon, and wear the polishing metal. 10, Key Tank is a depression area of u200bu200bthe pressure-mold guide, and the driving force when the mold is transferred. This surface is only easy to worn in the stamping or key size hours, and starting at the beginning of the installation. The knocking effect of the keyway is caused by loose keys. When the key is supported on the keyway, the wall in the keyway generates an arcade effect. 11, Ring Dynamic Damage Analysis: (1) The domestic material used in the ring model is unstable, uneven, there is part Stress (lost by the blank supplier); (2) The opening rate of the ring model is too high (should be customer requireme), causing the strength of the ring dil, dough decline ; – Biped Feed, ServiceThe thickness of animal husbandry (3) ring is too thin (customer proposes not to release segme), with the intensity of the ring mode; (4) Ring Dynamic During operation,Squeeze (such as a metal product such as a bearing ball in the granulation cavity); (5) Ring Mode is eccentric during installation or uniformThe force (with the coefficient of pressure roller assembly) causes a ring mode to constantly accept the unidirectional impact.
