LIMA Fish Feed Machine,Chicken Feed Machine
First, the pulverizer must be fixed, while the axis of the pulverizer and the power motor leather pulley should be parallel, the two-pass belt wheel groove must be on the same line, otherwise, not only the machine is damaged, but also easy to drop the belt. WM2 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
Second, if you need to change the pulley, you must perform the need to meet the main shaft speed of the pulverizer. The spindle speed cannot be increased at will, and when the speed rated is 15%, the machine will cause dramatic vibration. WM2 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
Third, the raw materials should be carefully cleaned in advance, and they will be sieved or selected, prevent iron parts, stone, etc. Inside the machine. WM2 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
Before each use, you must open the crushed machine cover. There is no damage to the parts in the inspection, especially the rotor. Whether the opening pin is in good condition, the connection is loose. When the confirmation is good, then close the cover, screw the handwheel on the machine. Drag the belt with hand, check whether the sports part is flexible, there is no abnormal sound and card tissue. WM2 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
Five WM2 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
Sixth, the operator should be tightened, wearing a mask, strictly prohibit wearing gloves; feeding should stand on the side of the crusher To prevent rebound debris to hit the face; when crushing long stem crops, hands can not be tightened, and shielded by crops. WM2 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
Seven Until the load is normal, maintain continuous and uniform, prevent ldquo; plugs rdquo ;. WM2 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
Eight Or pop up the injured person, do not allow the hand to enter the tissue dial, which can be pushed into the pulverizing chamber with a harder stem bar. WM2 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
Nine It is strictly forbidden to use a wooden stick or hand to feed or pull out the material to avoid hurt the arm or damage the machine. WM2 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
10, it is strictly forbidden to open when the crusher is runningMachine door; belt drive should be set; for long-term overload operations; various tools must not be placed on crusher and material, so as not to fall into the machine; the workplace is forbidden, pay attention to waterproof and moisture. WM2 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
Eleven, the self-made powder bag should adopt a breathable fabric, the length is not shorter than 1.5 meters. If the pink bag is not breathable or too short, it is possible to cause the feed port to reverse. WM2 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
Twelve . WM2 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
WM2 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
WM2 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry There is a gate or beater in the lower part of the stroke. The amount of feed can be controlled by adjusting the opening degree of the shutter or the baffle. For example, when machining mountain vines, the vines should be chipped, and the length should not exceed 150 mm. By controlling feeding, work efficiency and pulverizing quality can be improved to avoid overload.
WM2 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
There are two-three-screen screens of different apertures, and replace different apertures when used. Different pulverized particles. When installing the screen, according to the direction of rotation of the rotor, the lab position at the screen connector should be correctly selected, the inner interface direction is the same as the rotten direction, so as to avoid blocking; if the screen screen is tapered, due to the small hole end There is usually a small amount of burrs, for easy discharge, the large hole end should be facade.
WM2 China Feed Industry Information Network – Based on Feed, Service Animal Husbandry
When the pulverizer is used to adjust the pulverized particle size, it can also be controlled by the size of the adjustment damper. WM2 China Feed Industry Information Network – Based on Feed, Serving Animal Husbandry
