Method for adding molasses in fit feed

LIMA Fish Feed Machine,Chicken Feed Machine

Sugar honey is a very good feed raw material, which is very common in Europe and Some countries in Asia. This is because the molasses are not just one of the most raw materials, but also have the advantages of digestion and absorption, improved horizontal, reduce dust, improve particle quality. However, the use of the feed industry in my country is limited. The reasons are stored as an axillar, and the transportation requires specialized tools. Another important reason is that the viscous liquid as a fluidity is added as convenient to other liquids in the feed processing. This article discusses the addition of molasses and some key technologies in the feed. the Physical Characteristics of Livestock 1 Sugar Honey is a by-product of sugar industry in sugar cane, beets. Due to technical cost, etc., extracting sugar is no longer economical, and its residue is a glucogene. In the past, the sugar industry has been called waste honey. It is a dark brown liquid with a fluidity. The viscosity at room temperature is approximately 3 to 8pa.s. There are two ways to reduce their viscosity: heating and reducing dry matter content. Catching high temperature improves its liquidity is a very effective and common method. The temperature of the molar is increased by 5 ¡ã C, and its viscosity is halved. At 40 ¡ã C, its viscosity is approximately 1.0 pa.s. However, if the temperature is too high, it will produce a coking sugar for a long time, it hinders flow. The dry matter content of molasses has a great effect on its fluidity. When the dry matter content is between 72% to 78%, the dry matter content is reduced by 2 percentage poi, and its viscosity is halved. Reducing the content of dry matter is generally diluted with other liquids such as water, oil or the like. However, this will make the adding process more complicated. Therefore, this method is generally not used. Sugar content is typically between 42% to 50%. Although its energy density is lower than corn, it is very good than corn, and the digestion is quickly absorbed and has a price advantage. Some experime have shown that plaques are added to pig feed to replace the same amount of energy-inflammatory feed, and pigs’ food will increase by 9% to 12%. The daily gain increases but the feed rate is slightly reduced. An experiment made by the British Ministry of Agriculture shows that adding 2% of the glucosome in broiler feed, with a total weight of the whole feeding cycle (49D), the total weight of 40go feed conversion is 0 ~ 21 days old, the sugar honey group is obviously high In the control group. The entire feeding cycle is not big. The effect of reducing dust in the feed is also very obvious. Especially the duck feed, due to the special feeding of ducks, the dust level of its particle feed is very strict, generally not commercially 2%. Therefore, many manufacturers in Europe use sugar to reduce dust, which is up to 5%. According to the experiment of a chicken feed, 2% of the gangmele added to the growth of chicken feed is 5.7, add 3% molasses, and the improvement rate is 6.8%; add 2% of the sweets in the chicken feed. The improvement rate is 26.7%; the increase of 3% is 28.8%. It can be seen that the improvement in the quality of the particulate feed is obvious on the quality of the particulate feed. And the divers, the more obvious the effect. 2 Sugar Honey in TeamAddition in the material is added to the feed processing process, with the following types of molasses: Add, add, granulated spraying, and use special addition equipment in the strontium. Services Livestock 2. Add Many feed mills in the mixer want to add saccharin in the mixer. This is because the mixed processes of most feed mills are batch constitue. Therefore, adding to the maximum, real-time control and recipe management in the mixer. However, the molasses cannot be sprayed in a mixer like other liquids. The specific method is to open two holes in the second half of the horizontal mixer, is equipped with an aliquot of the helical direction, attached to the electric or pneumatic ball valve and connected to the pHI; 50 mM. The addition method is after the mixer is mixed with 35s, the two ball valves are open, and the open time is 3 to 5 s. The duration is up to 30s. This is because the mixing cycle has time limit, if the valve opening time is too long, it is difficult to mix, it is difficult to mix; if the total amount of feed time is too long, it will affect the mixing quality. It can be seen that the amount of adding is not too high in the mixer, up to 2%. Otherwise it will affect the mixing quality. It is different from the addition of the biaxial mixer. A long e is added axially in the mixer, which is a small hole hng a diameter of 10 mm. The position of the small hole varies from the distance from the inlet of the sugar honey. Sugar honey inlet plus electric (pneumatic) valve. After the material enters the mixer and mix 5s, open the valve to start adding a glucogene. Duration up to 15S. The amount of addition of this method is not too high; up to 5% can be added. 2.2 Adding this method in the strontium and is relatively convenient, and it is also a way to use more European countries. The molasses are mixed with steam in the steam of the appersulars, and the saccharin is blown into the regulator after the temperature and pressure of the steam. Here, due to the borrowing steam, the maximum amount of adding quality of the mola honey is greatly improved. The amount is up to 10%. For some feed mills using a ripening tank, the amount of molasses can be added more than 10% for the feed mill of the usual and urination. However, this approach is not enough. First, the conditioner needs to be cleaned regularly, and the other is difficult to implement real-time control. Since the formulation of the feed is carried out by batches, the addition of the molasses is a continuous addition process. Therefore, it is difficult to automate real-time control of formulation management. To add sugar to the formulation to add continuous signals into the recipe management program in the amount of the formulation. This will inevitably generate errors between formulation management and actual addition. Therefore, another set of control systems are used in general. – Based on Feeds, Serving Livestock 2.3 Granulation After the spraying is generally not pure saccharin after granulation, mostly a m ure of molasses. Pure sugar spray is very difficult. Even if heating is difficult to spray evenly. And after spraying, it will also cause difficulties in subsequent packaging, delivery, and the like. European countriesAfter development, spraying products typically use liquid fat and mixed with molas. This not only reduces the viscosity of the molase makes the spraying easier, but also improve the appearance of the particles, improve the premium. It can also reduce the feed cost. Mixing molasses with other liquid mixed materials, or add some materials such as vitamins such as vitamins such as vitamins such as vitamins under high temperature conditions, and believe that market prospects will certainly be very broad. 2.4 Sugar Honey Dedicated Add Equipment Sugar Mask Special Add Equipment European Use Comparative. my country has been developed as a rarch project during seventh fifteenth period and has been developed by the original business department, but has not formed a commercial application. Moreover, the viscosity of the standard formulated saccharin is 10.2 Pa.s. is also not practical. Under normal circumstances, unpudiluated molasses are far less than 0.2 Pa.s. Of course, the temperature is too high (greater than 40 ¡ã C), as described above, is a coking sugar. Its mixed uneven coefficient (CV) is not more than 10% and 7% of the general mixer also has a distance. Although the m ure of glucosome is uneven is not much affected by the feed mass, it has a certain impact on the external quality of the product. The highest amount of such equipment is usually about 5%. 1 / 2 1 2 Next Last

Please feel free to give your inquiry in the form below. we will reply you quickly!

    LIMA Machinery